chemical industry gas steam normal pressure water tube boiler
HOT
Capacity:1-20t/h
Rated thermal efficiency: 100-104%
Fixed working pressure: ≤1.6MPa
Applicable fuel:natural gas etc.
HOT
Capacity:0.7-14MW
Rated thermal efficiency:96-98%
Fixed working pressure:≤1.25MPa
Applicable fuel:Natural gas, light oil, etc.
HOT
Capacity:0.7-2.8Mw
Rated thermal efficiency: 97.2-106%
Fixed working pressure:0.1MPa
Applicable fuel:Natural gas, etc.
HOT
Capacity:2.8-7.0Mw
Rated thermal efficiency:≥105.5%
Fixed working pressure:-0.02MPa
Applicable fuel:Natural gas, etc.
HOT
Capacity:99Kw
Rated thermal efficiency:97.2-104.4%
Fixed working pressure:1.0MPa
Applicable fuel:Natural gas, etc.
HOT
Capacity:0.5-4.0 t/h
Rated thermal efficiency:98%
Fixed working pressure:≤1.25MPa
Applicable fuel:electric energy
Oxygen-blown coal gasification captures CO 2 from gas having a high CO 2 content of about 40% under pressure ranging from 2.5 megapascals to 3.0 megapascals (pre-operation CO 2 capture), so that the gas flow to be treated is lower than the CO 2 content to be captured (post-operation CO 2 capture) from the boiler exhaust gas.Get Price
When an excess supply of exhaust or low-pressure steam is already available, there is little justification for installing heat recovery equipment. If economically justified, boiler water blowdown can be used to heat process streams. In most cases, boiler water blowdown heat recovery systems use flash steam from the flash tank for deaeration.Get Price
Typically, boiler pressures used in steam blowing provide a dynamic pressure throughout the piping that is at least 20% higher than would be experienced in normal operating conditions (CFR ≥ 1.2). Any potentially damaging particles will be blown out of the piping prior to plant operation.Get Price
Fire Tube Boilers. In a fire tube steam boiler, the tubes on the boiler are heated, and the water circulates around the tubes. The heat inside the tubes is produced by gases heated by coal or oil, and it is transferred by thermal conduction to the water to create steam. Fire tube steam boilers produce low pressure steam.Get Price
Typically, boiler pressures used in steam blowing provide a dynamic pressure throughout the piping that is at least 20% higher than would be experienced in normal operating conditions (CFR ≥ 1.2). Any potentially damaging particles will be blown out of the piping prior to plant operation.Get Price
Combined-cycle power plants (Fig. 2.3) are compound gas turbine–steam turbine systems wherein the extreme hot exhaust from a gas turbine is employed to run a boiler, and the steam thus produced is fed into a steam turbine to generate power.These plants can deliver high power output at efficiencies as high as 50%–60% with low emissions and produce 50% more …Get Price
Oxygen-blown coal gasification captures CO 2 from gas having a high CO 2 content of about 40% under pressure ranging from 2.5 megapascals to 3.0 megapascals (pre-operation CO 2 capture), so that the gas flow to be treated is lower than the CO 2 content to be captured (post-operation CO 2 capture) from the boiler exhaust gas.Get Price
The amount of steam produced is typically about 3.5 kg per kg black liquor solids, but can range from 2.5 to about 3.8 kg steam per kg black liquor solids, depending on the thermal efficiency of the recovery boiler. The high pressure steam is passed through a steam turbine to generate electricity. Depending on the quality of theGet Price
Fire Tube Boilers. In a fire tube steam boiler, the tubes on the boiler are heated, and the water circulates around the tubes. The heat inside the tubes is produced by gases heated by coal or oil, and it is transferred by thermal conduction to the water to create steam. Fire tube steam boilers produce low pressure steam.Get Price
Combined-cycle power plants (Fig. 2.3) are compound gas turbine–steam turbine systems wherein the extreme hot exhaust from a gas turbine is employed to run a boiler, and the steam thus produced is fed into a steam turbine to generate power.These plants can deliver high power output at efficiencies as high as 50%–60% with low emissions and produce 50% more …Get Price
Furnace wall water cooling – eliminates refractory and related maintenance. Gas-tight setting membrane – inhibits dew-point sulfur corrosion and outages caused by gas leaks. Rugged steel-based frame – supports boiler and allows jacking and skidding. Outer lagging – galvanized, weather-tight for outdoor installations. Drum internals – ensure positive circulation, low …Get Price
The water in the tube becomes more concentrated, increasing the potential for deposition of boiler water salts. In extreme cases, deposition becomes heavy enough to reduce circulation to a point at which premature steam-water separation occurs. When this happens in a furnace tube, failure due to overheating is rapid.Get Price
When an excess supply of exhaust or low-pressure steam is already available, there is little justification for installing heat recovery equipment. If economically justified, boiler water blowdown can be used to heat process streams. In most cases, boiler water blowdown heat recovery systems use flash steam from the flash tank for deaeration.Get Price
The water in the tube becomes more concentrated, increasing the potential for deposition of boiler water salts. In extreme cases, deposition becomes heavy enough to reduce circulation to a point at which premature steam-water separation occurs. When this happens in a furnace tube, failure due to overheating is rapid.Get Price
Aug 24, 2017 · Pump stands take your incoming water, whether cold or hot (the latter of which requires a boiler, which DuGoff highly recommends for self-serves, since chemicals are more effective hot than cold), and mixes the chemical solutions. The pump stand also sends those solutions to the bays.Get Price
Sep 01, 2014 · In some cases, the last rinse is treated with chemical to raise the pH to a normal boiler pH range, and the boiler is fired to 180F to 200F so that it can be drained hot and dried out.Get Price
The cleaning is performed when a boiler is filled with a water-based chemical solution. The solution is heated either by starting the boiler itself or by using steam from an external boiler. Maintaining the conditions above the boiling point, chemical concentration, and oil content are monitored for a certain period of time or until the oil Get Price
The cleaning is performed when a boiler is filled with a water-based chemical solution. The solution is heated either by starting the boiler itself or by using steam from an external boiler. Maintaining the conditions above the boiling point, chemical concentration, and oil content are monitored for a certain period of time or until the oil Get Price
Hot water heating boiler. A boiler in which no steam is generated, from which hot water is circulated for heating purposes and then returned to the boiler, and that operates at water pressures not exceeding 160 pounds per square inch gauge (psig) (1100 kPa gauge) and at water temperatures not exceeding 250°F (121°C) at or near the boiler outlet. Hot water supply boiler.Get Price
Furnace wall water cooling – eliminates refractory and related maintenance. Gas-tight setting membrane – inhibits dew-point sulfur corrosion and outages caused by gas leaks. Rugged steel-based frame – supports boiler and allows jacking and skidding. Outer lagging – galvanized, weather-tight for outdoor installations. Drum internals – ensure positive circulation, low …Get Price
Sep 01, 2014 · In some cases, the last rinse is treated with chemical to raise the pH to a normal boiler pH range, and the boiler is fired to 180F to 200F so that it can be drained hot and dried out.Get Price
k. Superheater, drums and boiler tube system maximum design pressure, Vendor to specify, but a minimum of 300 kPa (3 bar) above operating pressure is required. l. Steam drum and boiler tube system maximum design temperature specified on data sheet, superheater design temperature per …Get Price
Feel free to reach out if you want to collaborate with us, or simply have a chat.
